{"id":3530,"date":"2026-10-21T15:45:30","date_gmt":"2026-10-21T07:45:30","guid":{"rendered":"http:\/\/www.drgoodarzi.com\/blog\/?p=3530"},"modified":"2026-10-21T15:45:30","modified_gmt":"2026-10-21T07:45:30","slug":"what-is-the-ratio-setting-on-an-expander-48e1-a8ded5","status":"publish","type":"post","link":"http:\/\/www.drgoodarzi.com\/blog\/2026\/10\/21\/what-is-the-ratio-setting-on-an-expander-48e1-a8ded5\/","title":{"rendered":"What is the ratio setting on an expander?"},"content":{"rendered":"

Hey everyone, it\u2019s Jake here from the compressor and expander side of the business\u2014just got off a call with a process plant engineer who was stressed AF about expander ratio settings, so I figured I\u2019d break this down straight, no stuffy engineering jargon that makes your eyes glaze over. If you work with expanders (or even just mess around with process equipment for a living), you\u2019ve definitely seen \u201cratio setting\u201d pop up in specs, control panels, and troubleshooting guides. And if you\u2019ve ever messed that setting up? It\u2019s like trying to bake a cake with 2x the required baking powder\u2014total disaster, either it barely runs or it blows out (literally, sometimes). Let\u2019s dive into what this ratio actually is, why it matters, and how to nail it right, plus why getting it wrong on your expander can cost you way more than just a few extra hours of downtime. Compressor And Expander<\/a><\/p>\n

<\/p>\n

First off, let\u2019s get super basic: an expander takes high-pressure, high-temperature process gas (think natural gas, refinery feedstock, even air for some industrial uses) and expands it to a lower pressure, right? That expansion turns all that thermal and pressure energy into mechanical work\u2014either to spin a compressor, generate power, or both (we call those combined turboexpanders, and they\u2019re my favorite type to sell because of how versatile they are). The \u201cratio setting\u201d here is simple: it\u2019s the pressure ratio between the expander\u2019s inlet (where the gas comes in) and the outlet (where it leaves after expansion). I know, I know\u2014you\u2019re thinking \u201cisn\u2019t that just inlet pressure divided by outlet pressure?\u201d Yeah, exactly, but it\u2019s not a random number you pull out of thin air. It\u2019s calibrated specifically for every single expander, because messing with that ratio changes literally everything\u2014from how much energy you get out to how long the unit lasts.<\/p>\n

Wait, hold on\u2014let\u2019s make that concrete. Let\u2019s say we\u2019ve got a typical natural gas processing expander that runs at 120 psia inlet and 30 psia outlet. That\u2019s a 4:1 pressure ratio, right? If I crank the outlet valve so that the outlet drops to 20 psia, suddenly that ratio jumps to 6:1. Sounds like more energy, right? But here\u2019s the catch: expansion ratios that are too high make the gas cool way too fast (we call that Joule-Thomson effect, but don\u2019t worry about the fancy name\u2014just know fast cooling means water or even CO2 can condense into solid ice or dry ice, and that crap clogs the expander blades faster than leaves clog a gutter in fall. I\u2019ve seen a client\u2019s unit go down in 3 days because they set the ratio too high, and it took us 12 hours to strip it down and clear the solid buildup. Not a good look for their production schedule.<\/p>\n

On the flip side, what if you set the ratio too low? Let\u2019s take that same expander, 120 psia inlet, keep the outlet at 50 psia\u2014now that\u2019s a 2.4:1 ratio, way lower than the 4:1 it\u2019s tuned for. What happens here? The expander isn\u2019t doing enough work to move the load it\u2019s paired with. So if it\u2019s running a natural gas liquefaction compressor, the compressor can\u2019t pull enough gas, and your plant\u2019s throughput drops by 15-20%\u2014that\u2019s lost revenue, every single hour. For a power-generating expander, you\u2019re leaving kilowatts on the table, which adds up to thousands a month if you run it off-spec.<\/p>\n

Now, why do we care about this from a supplier perspective? Because I\u2019m not just selling a hunk of metal with blades and a casing\u2014we build expanders that are matched to our clients\u2019 exact process, and the ratio setting is non-negotiable for optimal performance. Wait, but who actually sets this ratio? Is it up to our techs when we ship the unit, or is it something the plant\u2019s operators adjust? Both, honestly. We calibrate the base ratio during factory testing, but sometimes process conditions change\u2014like if inlet pressure fluctuates because another unit in the plant is down, or outlet pressure shifts as the plant\u2019s throughput ramps up. That\u2019s when operators need to tweak the ratio, but they have to do it smartly.<\/p>\n

Let\u2019s get into how to calculate the right ratio for your expander, because I get that not everyone has an engineer on call 24\/7. First, you need two numbers: the actual inlet pressure of the gas going into the expander (measured at the nozzle, not just the supply line\u2014those can be different because of pressure drops) and the required outlet pressure for the process downstream. Don\u2019t use gauge pressure, use absolute pressure\u2014gauge pressure is 0 at atmospheric, but absolute is 0 at a total vacuum, which is what matters for accurate expansion math. So if your inlet is 100 psig (psig = gauge) that\u2019s 114.7 psia (add 14.7 for atmospheric), and your outlet needs to be 20 psig, that\u2019s 34.7 psia. Divide 114.7 by 34.7, and your ideal ratio is ~3.3:1. That\u2019s your sweet spot.<\/p>\n

But wait\u2014there\u2019s a hidden factor here: gas type. Natural gas is mostly methane, but it can have ethane, propane, even CO2, and all those heavy hydrocarbons change how the gas expands. If you\u2019re processing a gas with a lot of heavier components, your max safe ratio is a little lower because those heavy parts can condense easier than pure methane. We always run a gas composition analysis when we design an expander for a client, so we can flag the safe ratio range for their exact mix. I once had a refinery client who wanted to bump their expander ratio to get more power, but their gas had 18% propane\u2014our techs told them the max safe ratio was 4.2:1, not 5:1, because propane would condense into liquid in the expander, eroding the blades. They listened, and their unit ran for 18 months without a blade issue. That\u2019s why we don\u2019t just give generic ratio numbers\u2014we tailor them to the gas and the load.<\/p>\n

Another thing people forget: the ratio setting ties directly to the expander\u2019s efficiency curve. Every single expander we build has a specific efficiency curve that peaks at the designed ratio. Go above or below that, and efficiency drops fast. A 10% off-ratio setting might only knock 5% efficiency at first, but keep it there for weeks, and that drops to 15%\u2014for a 1 MW expander, that\u2019s 150 kW of lost power, which at 8 cents per kWh is $10,512 a month down the drain. That\u2019s not pocket change, that\u2019s a new delivery truck or two for their operation.<\/p>\n

Now, what about when you actually have to adjust the ratio? Let\u2019s say your plant ramps production up, so inlet pressure jumps from 100 psia to 120 psia, and you need to keep outlet pressure the same. How do you adjust the ratio without messing things up? First, check your process specs\u2014don\u2019t just guess. If you\u2019re not sure, call your supplier\u2019s tech support (shoutout to my team\u2014we\u2019re on call 24\/7 for this stuff). When adjusting, make small changes, not big jumps. If your current ratio is 3.3:1, moving to 3.5:1 is fine, but jumping to 5:1 is a no-go. And always monitor for temperature changes at the outlet\u2014if it drops 50\u00b0F or more in a short time, you\u2019re pushing the ratio too high, and risk condensation buildup.<\/p>\n

I get that sometimes operators get tempted to tweak the ratio to squeeze a little more performance out of an old expander. Maybe the unit is 10 years old, and they think \u201cif I crank the ratio a little, I can get another 5% work out of it.\u201d Just don\u2019t. Old expanders might have tiny blade erosion from years of operation, so their max safe ratio is even lower than when they were new. Cranking it too high on an old unit can cause blade failure, which means an emergency shutdown that costs way more than the extra work you get from the ratio tweak. We\u2019ve seen this too many times\u2014client calls us at 2 a.m. because their expander blew a blade, and it takes 3 weeks to get a replacement, costing them millions in downtime.<\/p>\n

Now, let\u2019s tie this back to what we do as compressor and expander suppliers. We don\u2019t just sell a unit and walk away. Every expander we ship comes with a full ratio calibration sheet, tailored to the client\u2019s process, gas composition, and load requirements. We also provide 24\/7 technical support for ratio adjustments, troubleshooting, and even regular audits of your expander\u2019s ratio and efficiency. A lot of our competitors just send a spec sheet and say \u201cgood luck,\u201d but that\u2019s not how we roll. We\u2019re part of our clients\u2019 teams, so when their process changes, we help them adjust the ratio safely to keep their operations running smooth.<\/p>\n

Wait, let\u2019s address a common myth I hear all the time: \u201cRatio is just a pressure number, so I can set it with the control panel\u2019s pressure inputs.\u201d No, not exactly. The control panel has setpoints for pressure, but the ratio is the relationship between inlet and outlet, so you can\u2019t just set an outlet pressure without checking inlet pressure first. If inlet pressure fluctuates, outlet pressure will shift unless you adjust the ratio accordingly. For example, if inlet drops 10 psia, outlet will drop too if you leave the ratio the same, so you have to adjust the outlet valve to get back to your desired ratio. Our techs train operators on this during the commissioning phase, so they don\u2019t get stuck guessing when things go off.<\/p>\n

Another point: if you\u2019re working with a turboexpander that\u2019s paired with a generator, the ratio setting directly affects power output. We have a formula we use for our clients to estimate power at different ratios, so they can plan their production accordingly. For example, a ratio of 3:1 gives X kW, 3.5:1 gives X + 12% kW, 4:1 gives X + 20% kW\u2014but only if that ratio is within the safe limit for their gas. That formula isn\u2019t generic, either\u2014it\u2019s based on the actual design of the expander we built, so it\u2019s accurate for their unit.<\/p>\n

Let\u2019s wrap this up with a real quick checklist, because I know you\u2019re here for actionable stuff. To get your expander ratio right every time:<\/p>\n

    \n
  1. Use absolute pressure, not gauge, for inlet and outlet measurements.<\/li>\n
  2. Factor in your exact gas composition (heavy hydrocarbons mean lower safe max ratio).<\/li>\n
  3. Stay within 10% of your designed ratio\u2014beyond that, efficiency drops fast and damage risk goes up.<\/li>\n
  4. Adjust ratios in tiny increments, and monitor outlet temperature for sudden drops.<\/li>\n
  5. If you\u2019re unsure, hit up your supplier\u2019s support team\u2014we\u2019re here to help, not make you feel silly for asking.<\/li>\n<\/ol>\n

    At the end of the day, the expander ratio setting isn\u2019t just a line item in a spec sheet\u2014it\u2019s the make-or-break setting for your unit\u2019s performance, longevity, and your plant\u2019s bottom line. Mess it up, and you\u2019re looking at downtime, lost revenue, or even equipment damage. Nail it, and your expander will run smoothly, efficiently, and pay for itself over and over again.<\/p>\n

    <\/p>\n

    If you\u2019re dealing with an expander that\u2019s off-spec, getting too much downtime, or just want to optimize your ratio settings to boost your performance, reach out to our team for a consultation. We\u2019ll send one of our experienced techs to your site, run a quick audit, and help you get that ratio dialed in right\u2014no guesswork, no jargon, just straight solutions for your operation.<\/p>\n

    Cryogenic Liquid Storage Tank<\/a> References:<\/p>\n

      \n
    1. Boyce, M. P. (2012). Gas Turbine Engineering Handbook. Butterworth-Heinemann.<\/li>\n
    2. Process Expander Fundamentals and Applications. The American Society of Mechanical Engineers (ASME).<\/li>\n
    3. Compressor and Expander System Design Best Practices. Hydraulic Institute and Turbo Machinery Manufacturers Association.<\/li>\n<\/ol>\n
      \n

      Xinxiang Jiale Intelligent Equipment Co., Ltd.<\/a>
      As one of the most professional compressor and expander manufacturers and suppliers in China, we’re featured by quality products and good service. Please rest assured to buy durable compressor and expander for sale here from our factory. We also accept customized orders.
      Address: No.3913, 9th Floor, Unit 3, East Commercial and Office Complex, Baolong City Plaza, Hongqi District, Xinxiang City, Henan Province, China
      E-mail: cc2397410@gmail.com
      WebSite:       https:\/\/www.jiale-asu.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

      Hey everyone, it\u2019s Jake here from the compressor and expander side of the business\u2014just got off … What is the ratio setting on an expander?<\/span>Read more<\/a><\/p>\n","protected":false},"author":880,"featured_media":3530,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3493],"class_list":["post-3530","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-compressor-and-expander-4804-a919e4"],"_links":{"self":[{"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/posts\/3530","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/users\/880"}],"replies":[{"embeddable":true,"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/comments?post=3530"}],"version-history":[{"count":0,"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/posts\/3530\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/posts\/3530"}],"wp:attachment":[{"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/media?parent=3530"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/categories?post=3530"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.drgoodarzi.com\/blog\/wp-json\/wp\/v2\/tags?post=3530"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}